Broward County, Florida
Industrial Concrete Floors in Broward County
Slabs placed flat, joints that hold up to forklifts, finishes that last.
In short
Who handles industrial concrete floors in Broward?
Unified GCS builds and repairs industrial concrete floors in Broward County for warehouse owners, distributors, manufacturers and marine operators. The work involves placing new slab-on-grade panels, rebuilding and filling damaged joints, repairing cracks and spalls, and grinding, polishing or coating the slab so it stands up to forklift traffic and racking loads.
Industrial Floors · Broward
Industrial concrete floors in Broward County have to carry forklifts, pallet jacks and racking loads every day without breaking up at the joints. Unified GCS places new slab-on-grade floors, rebuilds and fills damaged joints, repairs cracks and spalls, and grinds, polishes or coats existing slabs. The goal is a flat, hard, cleanable surface that does not damage equipment or product.
Most floor problems start at the joints. Hard wheels strike an unsupported joint edge, the edge chips, and the damage widens with every pass. Curling at slab corners, dusting from a weak surface and cracks from settlement or overloading follow. We assess what is causing the wear, not just where it shows, and repair it with semi-rigid joint filler, rebuilt joint edges, crack repair and surface treatment suited to the traffic.
Written and reviewed by the Unified GCS project team, 45 years in concrete restoration and construction. Last reviewed October 2026.


Local conditions
Warehouse and distribution space in Broward County
Broward's industrial buildings are concentrated inland: around Port Everglades and the airport in Fort Lauderdale and Dania Beach, in the Pompano Beach and Deerfield Beach industrial districts along the rail and highway corridors, and in the newer distribution parks of Miramar, Davie and Sunrise. Much of the older stock in Pompano Beach and Oakland Park has floors that were never designed for current racking heights or lift truck traffic.
Land is tight, so operators here upgrade existing buildings more often than they build new ones. That means floor work is usually renovation: converting a general warehouse for food, pharmaceutical or e-commerce use, repairing joints before new racking goes in, or polishing a dusting slab. Industrial buildings over 3,500 square feet also fall under the county's Building Safety Inspection Program at 25 years, which can add structural repairs to the list.
Where this work is needed
Broward industrial districts and their floors
Floors near Port Everglades and Fort Lauderdale-Hollywood International Airport serve freight forwarding, cold storage and cargo handling, where slabs see heavy container loads, constant lift truck turns and, in refrigerated space, moisture at every door. West along State Road 84, the Marina Mile boatyards need thick pads and aprons for travel lifts and hauled-out vessels. Older multi-tenant bays in Pompano Beach, Oakland Park and Deerfield Beach, close to I-95 and the rail corridors, typically have thin, lightly reinforced slabs with wide, open joints.
Newer distribution buildings in western Broward, in Miramar, Pembroke Pines, Davie and Sunrise near I-75, I-595 and the Sawgrass Expressway, were built with larger panels and tighter flatness for high racking. The usual findings in these buildings are curled joints in the main aisles, cracks at column lines and wear at dock doors. Manufacturing and food-related tenants in the same parks often need a resinous coating or a polished floor that can be cleaned to the standard their own inspectors apply.
What is included
Industrial concrete floors in Broward County: scope of work
- 01New slab-on-grade placement and finishing
- 02Joint repair, filling and rebuilding
- 03Crack and spall repair
- 04Concrete grinding, polishing and densifying
- 05Epoxy and urethane floor coatings
- 06Loading dock, ramp and equipment pad repairs

Our approach
Floor work in an operating facility
We section the floor and work by zone, at night or over weekends, so receiving, picking and shipping continue. Each zone is cleared, repaired and returned on a schedule agreed with the operations manager. Joint filler, repair mortars and coatings are chosen partly for their return-to-traffic time, and we state that time plainly before work begins.
Grinding and polishing are done with dust collection at the machine. For new slabs and replacement panels we control subgrade preparation, reinforcement or dowels at the joints, placement and finishing, then saw-cut joints on time to control cracking. Loading dock aprons, ramps and equipment pads are handled in the same mobilization where they are part of the problem.
Unified GCS has 45 years in the business. See the full industrial floors service or everything we do in Broward County.
Planning the project
Planning floor work in an operating Broward facility
Floor work in a Broward warehouse is planned around the operation and the lease. Landlord and tenant first settle who is responsible for the slab, because many industrial leases assign floor repairs to the tenant and structural items to the owner. The work is then tied to a natural break: a tenant changeover, a racking reconfiguration or a slow season. Joint and crack repairs should be finished before new racking is anchored, so the installer is drilling into sound, level concrete.
Moisture is the planning issue specific to floor coatings in Broward. Slabs sit on ground with a high water table, and older buildings may have no vapor barrier under the concrete, so the slab is tested for moisture before a coating or resinous system is selected. New slabs, structural changes and dock modifications are permitted through the city building department, and the building official confirms whether a repair scope needs a permit. Exterior aprons and truck courts are poured outside the wettest months where the schedule allows.
How a project runs
From the first site walk to the closed permit.
- 01
Walk the property
We start on site with your manager, board or engineer and look at the conditions first-hand.
- 02
Define the scope
You get a written scope tied to the engineer's report or our findings, with the phasing spelled out.
- 03
Plan access and safety
Swing stages, shoring, barricades, parking and resident notices are set before the first cut.
- 04
Do the work
Our crews carry out the repairs in sequence, with inspections at the points the engineer requires.
- 05
Close it out
Final inspections, permit closure and a record of what was done, for the association's files.
Cities served
Industrial Floors across Broward County
Summary
Key takeaways for Broward owners and boards
- 01
Boatyards along Marina Mile on State Road 84 need thick concrete pads and aprons designed for travel lifts and hauled-out vessels.
- 02
Older warehouse bays in Pompano Beach and Oakland Park often have thin slabs with wide joints that break down under modern lift trucks.
- 03
Broward slabs are tested for moisture before coating, because the water table is high and older floors may lack a vapor barrier.
- 04
Joint and crack repairs in a Broward warehouse should be completed before new racking is anchored to the floor.
Questions
Industrial Floors in Broward: common questions
Can warehouse floor joints be repaired while our Pompano Beach facility stays open?
Yes. Joint repair is done aisle by aisle. Damaged edges are cut back and rebuilt, the joint is cleaned to full depth and filled with a semi-rigid filler that supports the edge under wheel loads. Most products allow traffic again within a short, defined window, which we confirm before scheduling.
Why is our warehouse floor in Miramar or Davie dusting?
Dusting means the top layer of the slab is weak, commonly from excess water at the surface during finishing or from poor curing. The fine powder gets into product and equipment. Grinding off the weak layer and treating the floor with a densifier, or polishing it, hardens the surface and stops the dust.
Do warehouses in Broward County fall under the Building Safety Inspection Program?
The program is not limited to condominiums. Under Board of Rules and Appeals Policy 05-05 it applies to buildings and structures at 25 years of age, with listed exemptions such as minor structures under 3,500 square feet. A licensed engineer or architect performs the inspection, and the building official confirms whether your property is included.
Who is responsible for floor repairs in a leased warehouse in Deerfield Beach?
The lease decides. Many industrial leases make the tenant responsible for maintaining the slab surface and joints and leave structural items to the landlord, but the wording varies. Read the lease or ask your attorney before approving work. We can document the floor condition with photos and a marked plan for either party.
Why are warehouse slabs tested for moisture before coating in Broward County?
Moisture vapor rising through a slab can blister or debond a coating. Groundwater is shallow across much of the county and older buildings may have no vapor barrier. On industrial concrete floors in Broward County we test the slab first, then select a system that tolerates the measured moisture or recommend polishing instead.
Can a boatyard or marine facility on Marina Mile in Fort Lauderdale get heavy-duty concrete pads?
Yes. Pads and aprons for travel lifts, forklifts and stored vessels are designed by an engineer for the wheel loads involved. We prepare the subgrade, place reinforcing and dowels as drawn, pour and finish the concrete, and cut the joints. Work is sequenced bay by bay so the yard keeps hauling and launching boats.
Regulations referenced
- Broward County Board of Rules and Appeals Policy 05-05: Building Safety Inspection Program
- Florida Statute 553.899: mandatory structural inspections for condominium and cooperative buildings
- Florida Statute 718.112: structural integrity reserve studies
This page is general information, not legal or engineering advice. Inspections are performed by licensed engineers and architects, and your building official sets the dates that apply to your property. Unified GCS is the contractor that carries out the repairs.
Referred by an engineer?
Have drawings, specifications or a full set of bid documents?
Most of our restoration, pool and roofing work comes to us through structural engineers, property engineers and board members. When the scope is already drawn and specified, we price exactly what is on the documents, flag anything that needs a question, and show every line so the board can compare bids fairly.
Request an estimate
Let's look at your building.
Send us the engineer's report, a few photos or a short description. We will schedule a site visit and follow up with a written scope.
- 45 years in the business
- Broward and Palm Beach counties
- Reply within one business day
Prefer to talk?(561) 678-4182
We reply within one business day. Your details are only used to respond to this request.