(561) 678-4182 Request an estimate

Stucco & Painting

Stucco, Facade Repair & Exterior Painting

Sound walls first, then a coating system that keeps the weather out.

In short

What is stucco and painting?

Stucco & painting is the repair of a building's cement plaster skin followed by a new protective coating system. The work removes loose stucco, repairs cracks, replaces failed sealant and recoats the walls. A building needs it when the facade sounds hollow, shows spreading cracks, chalks to the touch, or lets wind-driven rain through to the interior.

Stucco & Painting

Paint on a failing wall is money spent twice. We sound the facade, cut out delaminated stucco, repair the cracks and substrate, seal the joints, and finish with a coating system specified for coastal exposure.

Unified GCS has spent 45 years in this business. We carry out stucco & painting projects across Broward and Palm Beach counties for condominium associations, property managers, commercial owners and industrial operators.

Written and reviewed by the Unified GCS project team, 45 years in concrete restoration and construction. Last reviewed October 2026.

Stucco, Painting in South Florida by Unified GCS

Why it happens

Why facades crack, debond and let water through

Stucco is a thin cement plaster bonded to concrete or masonry, and it moves differently from the wall behind it. Daily heating and cooling, shrinkage and small structural movements produce hairline cracks, particularly at the corners of openings and where block meets a concrete column or beam. Wind-driven rain enters those cracks. Once water sits between the plaster and the substrate the bond weakens, the layer separates, and the surface begins to bulge and sound hollow.

The coating is the first line of defense for the wall, and the sun wears it down. Ultraviolet light breaks down the binder, the film chalks and thins, and it loses the flexibility that let it bridge fine cracks. Sealant joints around windows harden and pull away. On a reinforced concrete frame, rust stains or a straight crack in the plaster often mark corroding steel underneath, so the facade survey has to separate surface defects from structural ones.

What is included

Stucco & Painting: scope of work

  1. 01Stucco sounding, delamination removal and re-application
  2. 02Crack routing, sealing and patching
  3. 03Pressure cleaning and surface preparation
  4. 04Elastomeric and high-build exterior coatings
  5. 05Sealant replacement at windows, doors and joints
  6. 06Swing stage, scaffold and lift access

How we do it

How a facade is repaired and recoated

The facade is surveyed from a swing stage, scaffold or lift, and every drop is sounded. Hollow areas are marked and cut out to a firm edge. If the concrete or block behind is damaged, that repair is completed first to the engineer's detail. New plaster is applied over a bonding agent, or over lath where the specification calls for it, in coats that are allowed to cure and are finished to match the surrounding texture.

Cracks are treated according to their width and movement. Hairline cracks are usually bridged with an elastomeric patching compound, while wider or moving cracks are routed and filled with sealant. Old sealant at window and door perimeters and control joints is cut out and replaced over backer rod. The whole wall is then pressure cleaned to remove chalk, mildew and loose paint, and left to dry. New plaster needs its full cure time before coating because fresh cement is highly alkaline.

Coating starts with a primer or sealer matched to the surface, with an alkali-resistant product over new patches. The finish is applied in the number of coats and at the film thickness the manufacturer specifies, since an elastomeric coating only bridges cracks when it is built thick enough. Back-rolling works the material into the texture and closes pinholes. Work proceeds one drop at a time in suitable weather, and each elevation is inspected before the stage moves on.

Materials and systems

Stucco mixes, sealants and coating systems for coastal facades

Stucco repairs use portland cement plaster, either mixed on site from cement, sand and lime or supplied as a pre-blended, polymer-modified patching product with more consistent properties. Over concrete and block, a bonding agent or dash coat provides the grip, while over framed or dissimilar substrates the plaster is applied on corrosion-resistant lath with accessories such as casing beads and control joints. Near the ocean, galvanized or non-metallic lath and trim are preferred, because ordinary steel accessories rust and stain through the finish.

Exterior coatings are chosen by the condition of the wall. All-acrylic paints are breathable and hold their color on sound stucco. Elastomeric coatings build a thick, flexible film for walls with hairline cracking. Silicone-based coatings shed water while letting vapor escape, and penetrating clear sealers suit exposed concrete or masonry. Vapor permeability matters in a humid climate, since a film that traps moisture blisters. Primer, patching compound, sealant and finish should come from one manufacturer's system so that compatibility and warranty terms are clear.

What makes it last

What separates a paint job that lasts from one that peels

Coating failures on stucco are almost always preparation failures. Paint applied over chalk, mildew, salt or loose material bonds to the contamination instead of the wall. New plaster coated before it has cured and its alkalinity has dropped can burn the finish, leaving discoloration and loss of adhesion. Durable work includes full sounding of every elevation, pressure cleaning, a pH and moisture check on patches, the specified primer, and finish coats applied at the spread rate that produces the required dry film thickness.

A good facade proposal separates the stucco & painting scope into measurable items: square footage of delaminated plaster, linear footage of crack repair and sealant, and coating by elevation. Ask which sealant joints are included, what film thickness is specified and how it will be checked, and how landscaping, cars and windows are protected. Many coating manufacturers will inspect the preparation and issue a written warranty when their full system is used. Obtain that document before work starts.

Stucco & Painting work in progress

How a project runs

Planned around the people who use the building.

  1. 01

    Walk the property

    We start on site with your manager, board or engineer and look at the conditions first-hand.

  2. 02

    Define the scope

    You get a written scope tied to the engineer's report or our findings, with the phasing spelled out.

  3. 03

    Plan access and safety

    Swing stages, shoring, barricades, parking and resident notices are set before the first cut.

  4. 04

    Do the work

    Our crews carry out the repairs in sequence, with inspections at the points the engineer requires.

  5. 05

    Close it out

    Final inspections, permit closure and a record of what was done, for the association's files.

Summary

Stucco & Painting: key takeaways

  • 01

    Exterior paint lasts only as long as the wall beneath it stays sound, dry and free of chalk, salt and mildew.

  • 02

    Elastomeric coatings bridge hairline cracks only when applied at the dry film thickness the manufacturer specifies.

  • 03

    New stucco patches must cure and drop in alkalinity before coating, or the finish can discolor and lose adhesion.

  • 04

    Using primer, patch, sealant and finish from a single manufacturer keeps compatibility and warranty responsibility in one place.

Glossary

Terms you will see in the engineer's report

Sounding
Tapping a wall with a hammer and listening for a hollow note, which identifies stucco that has separated from the wall behind it.
Dry film thickness
The thickness of a coating after it has cured, usually stated in mils, which determines how well an elastomeric finish bridges cracks and resists rain.
Chalking
A fine powder that forms on a painted surface as sunlight breaks down the binder. Heavy chalking must be removed or sealed before recoating.
Control joint
A formed line in stucco that divides a wall into panels and gives shrinkage and thermal movement a planned place to occur instead of a random crack.
Lath
A metal or non-metallic mesh fastened to a wall to give stucco a mechanical key where it cannot bond directly to the surface behind it.

Questions

Stucco & Painting: common questions

Why repair the stucco before painting?

Coatings only perform on a sound, dry surface. Delaminated stucco and open cracks let water in behind new paint, where it blisters the coating and reaches the structure. Repairing first is what makes the paint job last.

How often should a coastal building be repainted?

There is no single interval. Coating life depends on the product, the film thickness applied, sun and salt exposure and the condition of the wall beneath. Chalking, fading, hairline cracking and failed sealant joints are the signs to watch. Many manufacturers tie their warranty to a set period, and a facade review near the end of it is sensible.

What is the difference between an elastomeric coating and regular exterior paint?

An elastomeric coating is applied much thicker and stays flexible, so it can stretch across hairline cracks and keep wind-driven rain out. Standard acrylic paint forms a thinner film that mainly provides color and weather protection. Which one suits a building depends on the wall condition and the manufacturer's system recommendation.

Can a building be painted during the rainy season in South Florida?

Yes, with planning. Coatings need a dry surface and enough time to set before rain, so crews watch the forecast, start on elevations that dry first and stop early when afternoon storms are expected. Patches and pressure-washed walls are given time to dry before coating. The manufacturer's data sheet states the temperature, humidity and recoat limits that apply.

Why do hairline cracks come back after a building is painted?

Hairline cracks reappear when the wall is still moving or the coating is too thin or too rigid to stretch across them. Cracks at window corners and where block meets a concrete frame open and close with temperature. Treating them with a flexible patching compound or sealant first, then applying an elastomeric system at full thickness, is what keeps them closed.

Can residents stay in the building during restoration?

In most projects, yes. Work is phased by elevation or stack, balconies are closed only while they are under repair, and notices go out before anything affects residents. We agree the sequence and access plan with the board and manager before work starts.

Do you work with our engineer?

Yes. Structural repairs are built to the specification of your engineer of record, and we coordinate inspections with them throughout the job. If you do not have an engineer yet, we can help you get started.

Standards and references

Repair methods and materials on every project follow the engineer's specification, the manufacturer's requirements and the building code in force. This page is general information, not engineering advice.

Referred by an engineer?

Have drawings, specifications or a full set of bid documents?

Most of our restoration, pool and roofing work comes to us through structural engineers, property engineers and board members. When the scope is already drawn and specified, we price exactly what is on the documents, flag anything that needs a question, and show every line so the board can compare bids fairly.

Request an estimate

Let's look at your building.

Send us the engineer's report, a few photos or a short description. We will schedule a site visit and follow up with a written scope.

  • 45 years in the business
  • Broward and Palm Beach counties
  • Reply within one business day

Prefer to talk?(561) 678-4182

Optional. For a large bid package, paste a download link in the message instead. Images or PDF, up to 50 MB.

We reply within one business day. Your details are only used to respond to this request.

Call Request an estimate